Usb Game Controller Driver Windows 8
How to Set Up USB Game Controllers on Windows 8. To set up USB game controllers on Windows 8, determine which controller.
***Read Below*** In a previous tutorial, I showed you how to connect your PS3 controller to the PC strictly using Motioninjoy for both USB and Bluetooth connections. The problem with Motioninjoy (in general) is that it requires the Internet, and can be buggy at times. This time around we are going to use the fantastic program called Better DS3 Tool, which allows you to configure your controller offline, no Internet required.
It works great in any current PC game that uses the Xinput profile (aka Xbox 360). Note 1: If you are having issues under Windows 8.1, make sure to try this guide below.
How To Download Anime From Kissanime Using Idm. Note 2: Run all programs as administrator to eliminate issues.
If you’ve recently upgraded to Windows 10 and now one of your USB devices isn’t working, read on. Whether it’s a USB mouse, keyboard, pen drive, printer, or some other USB device altogether, this guide should resolve your problem. Note that there are 5 possible solutions here. You may not need to try them all; just start at the top of the list and work your way down.
Method 1: Check if the device itself is faulty If the USB device was working before you upgraded to Windows 10, it’s unlikely to be faulty. But coincidences do occur. It’s certainly possible that your device just happened to die right at the same time that you upgraded Windows. So it’s best to rule that possibility out for sure before spending time on more complex troubleshooting. To check if the USB device is faulty, simply unplug it (‘Eject’ it if it’s a USB storage device) and plug it into another computer. If it works, the device is fine. If it doesn’t, then you’ve isolated the problem!
You just need to buy a replacement. Method 2: Check your power supply (laptop only) Your laptop’s power supply delivers power to your USB ports. If, for some reason, it fails to do this properly, the devices plugged into those USB ports may stop working. Sometimes, this can be fixed quite simply: 1) Unplug the power supply and charger plug from your laptop 2) Restart your laptop 3) Connect your USB device to the laptop again 4) Plug the power supply back in Method 3: Check your power management settings In order to save power, by default, Windows switches your USB controllers off when they’re not in use, and switches them back on again when they’re needed. Unfortunately, sometimes this approach doesn’t work as intended, and Windows fails to switch your USB controllers on again.
To rule this out as the cause of your USB woes, just stop Windows from ‘managing’ power to your USB controllers and devices: 1) Open Device Manager (type “Device Manager” in the Windows search field) 2) Expand the Universal Serial Bus controllers branch 3) Double-click the first USB Root Hub device in the list (if you see only one USB Root Hub device, that’s fine) 4) Click the Power Management tab 5) Un-check the Allow the computer to turn off this device to save power checkbox, and click OK. 6) Repeat steps 3-5 for each USB Root Hub device in your list of Universal Serial Bus controllers Method 4: Check your USB device drivers Your USB ports not working problem is probably being caused by driver issues. The steps above may resolve it, but if they don’t, or you’re not confident playing around with drivers manually, you can do it automatically with. Driver Easy will automatically recognize your system and find the correct drivers for it. You don’t need to know exactly what system your computer is running, you don’t need to risk downloading and installing the wrong driver, and you don’t need to worry about making a mistake when installing. You can update your drivers automatically with either the FREE or the Pro version of Driver Easy. But with the Pro version it takes just 2 clicks (and you get full support and a 30-day money back guarantee): 1) and install Driver Easy.
2) Run Driver Easy and click Scan Now button. Driver Easy will then scan your computer and detect any problem drivers. 3) Click the Update button next to a flagged USB driver to automatically download and install the correct version of this driver (you can do this with the FREE version). Download Uk Mortgage Calculator Excel. Or click Update All to automatically download and install the correct version of all the drivers that are missing or out of date on your system (this requires the Pro version – you’ll be prompted to upgrade when you click Update All). Method 5: Check your USB ports If none of the above methods resolve your problem, your USB ports might be damaged. To find out, you can take your PC to a repair store and ask them to check.
If your USB ports are damaged, the repairer should be able to replace them fairly inexpensively. I found something. By default fast startup is enabled in Windows 10. But it seems this way Windows is not loading usb devises. Sometimes it is but sometimes it isn’t.
By turning off fast boot my problems were solved. Disable/Enable quick boot Windows 10 1 Type Control Panel in the search box. 2 Click Control Panel. 3 Click Power Options. 4 Click Choose what the power buttons do. 5 Click Change settings that are currently unavailable.
6 Scroll down to Shutdown settings and uncheck Turn on fast startup. Click Save changes. Cheers 🙂 I hope this works for you too! Thank you Mark Bongers. After a day of many attempted fixes, yours worked for me.
FYI – boot time increased from 55 seconds to 62 seconds. After doing your fix and testing it, I restored the “fast startup” setting. Everything still works and boot time is back to 55 sec. Seems like Windows just doesn’t bother to turn the USB ports on in fast startup, but rather keeps the on/off setting from the previous boot.
My problems started with “anti malware” recommended by PC Magazine. It behaved badly.
The internet is a jungle. Microsoft is the pits. Thank you Mark!! This worked for me in seconds (and I did not even have to reboot!). Just unplugged the USB from my laptop, and plugged it back in, and presto chango – I’m printing! For reference, my specs: – Windows 10 – Lexmark x2690 printer – Dell Inspiron 17 7000 series laptop I had this problem when I first bought this laptop, and was able to resolve it (can’t recall how now, hence here I am today!). I believe the problem this time was due to the 11/3/2017 Windows Update: – Update for Windows 10 Version 1607 for x64-based Systems (KB4023057) Thank you again for the quick fix, Mark!
My keyboard/mouse stopped working. I connected to the computer via from another computer via remote desktop. A couple of the USB devices in Device Manager showed with yellow exclamations. I tried some stuff in another post and it did not work. Ultimately, I tracked down the hardware on the manufacturer’s site. They stated the stuff was not supported under Windows 10 (6+ year old computer). I downloaded the last Chipset driver they had for the MoBo and installed that.
While it was not listed as compatible with Win10, it works fine and fixed all the issues. Now if I could just figure out how to stop Windows Update from updating these drivers, the fix could be permanent. I suspect the solutions in this post will not work in my case, because mine is an age/compatibility related issue, but I may try them the next time it happens.
This has been happening to me since Windows 8. Updates (temporarily) kill all my ports *except* the USB 3 ports that are plugged into an internal connector on the motherboard. I’m guessing that either USB 3 ports are not affected OR the connector has a different driver than the other ones. Updating the drivers don’t quite work. A few (not all) of the USB drivers are from 2006, and updating causes all sorts of instability (it seems that Intel thinks the drivers can be updated, but MS does not.) Apparently my 5 year old motherboard (P8P67 Pro) is too old.
The PC still runs like a champ otherwise. When I boot up my computer my USB devices work fine for a short period of time.
But after 10 or 15 minutes, my USB WiFi adapter stops working. If I unplug it and put it in another port it begins to work again but will inevitably stop working again. I’ve tried the USB root hub power settings fix, I’ve tried the uninstalling of the root hub fix and neither of them have any long term effect and are generally useless.
It’s rather infuriating because my desktop didn’t have this issue when I first installed windows 10 and has only occurred after a few recent updates. I’ve run out of ideas of how to fix the issue and need help. The following, similar to first post above but with a little twist, has worked for me. Simple restart does not work. BUT shut down. Remove both power supply connection AND take out battery and leave out for about a minute. Take out your USB thumbdrive or whatever you have connected at same time, while shut down.
Replace battery and power supply, then power up. Once powers up, USB ports should be working just fine, no need to go through extensive procedures that may or may not work, leading likely to reinstall windows (and who wants that?!). Try the above first, anytime you have something screwy happening that does not respond to simply restarting. Has worked for me for more than one problem with windows 8 and 10 •.
After installing Windows 10, I had the yellow exclamation mark attached to all USB root hub entries (both chipset and USB 3.0 adapter card) in the device manager, showing error code 19 in their properties. None of my USB devices was functional. For me the solution was Microsoft’s explanation “This can occur when more than one service is defined for a device ()” ( ) I had a generic LibUSB driver from sourceforge.net installed under Windows 7 (for use with the Android debug bridge, I think) and it was updated during Win 10 installation. Uninstalling it under “Software” instantly freed up the USB ports. I was searching for this for two days in my free time and this site gave me valuable hints. Thanks to all contributors! Hi i have almost the same problem but mines like this: When i start the computer everythings fine But after the bios screen my keyboard and mouse dont work anymore I cant login to my windows But when i go to the bios menu right imitidatly after startup f8 My screen dont opens but my keyboard and mouse do still work.
Anyone know anything? I toke the battery out and started still the same And ps/2 mouse and keyboard didnt work too Cant get in to safety mode and menu All of my ports are doing the same So i cant do anything I have this computer for 8 months never had a problem Im out of options •. I had the issues in windows 10 of: Mouse cursor lagged no matter which port (but settled down on its own), but then soon no USB stick or larger USB drive would show up when plugged in.
(you could hear windows chime it knew it was there, but just acted like it didn’t exist). I couldn’t change the drive letter, because it didn’t even show up as a blank drive letter. I just tried turning off power management in the USB properties as shown in this post and BAM.problem solved after restart. Thanks for this. Hello every one, I have had a problem with my Window 10. When, I tried to back up form my Samsung 4.4 model through ” Smart Switch” program on my TOSHIBA lap top, it didn’t detect my phone. Just to mentioned, I did back up on Window 7 without any problems.
I checked the device managers, checked and changed the USB portal, it didn’t work at all. My phone, couldn’t be located in my computer as well. Could you please kindly advice me on how to solve the problem. I require to back up my phone, as it is running out of space. Hi, a family member upgraded their Acer Aspire e15 to windows 10 from Windows 8 – since then the HDMI connection to the TV is a bit wonky! When the HDMI cable is plugged in, the TV will say no video signal – then we take the laptop and connect it via a second HDMI cable to a different TV – works perfectly! Back to original TV and original cable and it works!
Usually stays working for the rest of the day and then it will stop again – repeat the above procedure and back up and running again! If anyone has any ideas I would be very grateful. I just upgraded my HP laptop from Windows 8.1 to Windows 10, and now 2 of the 3 USB ports won’t work. A simple mass storage device (4Gb Kingston USB stick) is not recognized on 2 ports, but is OK on the third. I’ve been installing/updating USB drivers for the past two days – no luck. Some deleted drivers re-appear on reboot.
USBview is showing that there is a ‘USB Composite Device’ on Port 3, eventhough there are no USB devices plugged in. In Device Manager, ‘USB Composite Device’ appears in the ‘Universal Serial Bus Controller’ list, rather than the ‘Universal Serial Bus Device’ list.
This is a load of horse and life’s just too short. What’s the best way to downgrade the machine to Windows 7?