Singer Manuals Free Pdf
Material fabric stitch power treadle, handcrank, add-on electric feed needle(s) one 15x1 (except VS1, which uses 20x1 ) The Singer Model 27 and later model 127 were a series of produced by the from the 1880s to the 1960s. (The 27 and the 127 were full-size versions of the Singer 28 and later model 128 which were three-quarter size).
They were Singer's first sewing machines to make use of ' technology. Millions were produced. They are all steel and were built before the advent of, and so they were designed to be repaired rather than replaced. Consequently many remain today, some in collections and others still in service. In company literature they were called 'the woman's faithful friend the world over'. Identification guide • Split slide plates running the entire depth of bed • Flat face plate, most are ornamented with but very early examples have a plain shiny finish.
Figure 1 from Whitehill's patent 326821 In the decade that followed, another gentleman applied his mind to advancing the state of the art. Scottish immigrant Robert Whitehill (1 June 1845 – 24 November 1903 ), founder of the Whitehill Manufacturing Company, became interested in sewing machines and subsequently patented an improvement to the take-up arm. He proceeded to manufacture his own machines from about 1875 until 1883. He then designed the sewing machine which would shortly become Singer's answer to the White machine. He applied for patent on 1 July 1884 and received US patent 326821 on 22 September 1885.
In his design Whitehill retained the White machine's dimensions and most aspects of its exterior; his contribution mainly consists of the new interior. That is, he rethought the entire powertrain—the mechanism that carries energy from the handwheel to the needlebar, to the bobbin driver, and to the feed dogs. He also conceived the bullet-shaped shuttle, which the White machine promptly adopted over its more traditional boat shuttle. Model 27 advertising card: 'This machine is unequaled' () He took his prototype to the Singer head office and showed it to the office manager James Bolton (1832–1916).
Bolton was thrilled with the machine and suggested a sewing competition against the best Singer models on-hand at the factory. Whitehill's prototype prevailed, and he sold the rights to it for 8,000 (USD 212,000 adjusted), with USD 1,000 held in reserve until he had perfected it for them. At the time, Singer was already selling two 'high arm' models (one a, the other an oscillating shuttle) which represented a new break from the company's established history of 'low arm' machines. The Whitehill design became the third Singer machine with a high arm, and quickly eclipsed the other two—neither of which Bolton liked anyway. The Whitehill machine took the name 'Vibrating Shuttle 1' when, two years later, it evolved into the improved 'Vibrating Shuttle 2'. Late 19th to early 20th century Singer sewing machine in Within a couple of years took notice, and printed the following praise for Whitehill's design, especially for its powertrain: Of Vibrating Shuttles These are shuttles of the long description, moving in a segment of a circle.
Download 2459 Singer Sewing Machine PDF manuals. User manuals, Singer Sewing machine Operating guides and Service manuals. Use this appliance only for its intended use as described in this manual. Use only attachments recommended by the manufacturer as contained in this manual. Free from accumulation of lint, dust, and loose cloth. As the owner of a new Singer sewing machine, you are about to begin an exciting adventure in.
There are several varieties. The most novel machine of this kind is the vibrating shuttle machine just produced by the Singer Manufacturing Company. In this case the shuttle itself consists of a steel tube, into the open end of which the wound reel is dropped, and is free to revolve quite loosely. Variation of tension is thus obviated in a very simple manner. The chief point of interest in the machine is undoubtedly the means employed in transferring the motion from the main shaft to the underneath parts, an arrangement as ingenious and effective as any device ever introduced into stitching mechanism.
It is the invention of Mr. Robert Whitehall [sic], and consists of a vertical rocking shaft situated in the arm of the machine[.] Motion is imparted to it by means of an elbow formed upon the main shaft acting upon two arms, called wipers, projecting from the rocking shaft, the angle formed by the arms exactly coinciding with that of the elbow in its revolution. This admirable motion will no doubt attract much attention from mechanists and engineers.
Production [ ] The 27 series had a long production run, including improved versions and many variants tailored to customer needs. Model 27-2 shown in an 1892 trade card () The model series evolved over time through these versions: Year Original name Currently AKA Notes 1885-1887 High Arm (VS version), Vibrating Shuttle 1, V.S. 1 experimental, very low production 1887-1891 Vibrating Shuttle 2, V.S. 2 Model 27-2*, Model 27 Fiddlebed shuttle overhauled 1891-1913 Model 27 bed changed to rectangular ~1910-1940s** Model 127 a 'modernized' 27—see 'Modernization' below • Not to be confused with the 27-2 variant; see Variations table below. • Many records from this era were lost during.
Portable versions [ ] A model 27/127 coincidentally weighs 27 pounds (12 kg), plus the weight of its motor, treadle, or hand crank, its light, and its case or cabinet. Such a weight strains the meaning of the term 'portable', even when fitted with only a hand crank and minimal wood case. (Today's typically weigh 3 to 5 pounds (1.4 to 2.3 kg).) This quickly led Singer to produce a 3/4ths size version intended for portability, exactly as the was doing with its new 3/4ths size ' machine. Singer's portable version evolved thus: Year Original name Currently AKA Notes ~1886-~1890 Vibrating Shuttle 3, V.S. 3 Model 28-1 evolved from the VS-2; bed changed to rectangular ~1890-1918 Model 28 Model 28-2 ~1910-1962 Model 128 a 'modernized' 28—see 'Modernization' below Modernization [ ] Models 127 and 128 are the 'modernized' versions of the 27 and 28, and carry the following improvements: • A new shuttle ejector button, invented in 1910, eases removal of the shuttle for rethreading. The button is located on the improved shuttle frame, Singer part number 54507, which can be retrofitted onto older model 27 and 28 machines. • The bobbin winder is mounted high on the pedestal, where a small rubber tire occupying its pulley makes contact with the motor belt.
The new mounting position solves the bobbin winder belt problem discussed later. • Dedicated motor mounting lugs, cast into the rear of the pillar, standardize the position of the motor bracket. A decade later, motor designs will settle down into a side-mounted motor that attaches to these lugs using an L-shaped bracket. • Automatic tension release when the presser bar is lifted, replacing the manual tension release achieved by pressing a spoon shaped device just below the tension regulator in the earlier machines.
This device is no longer present in the 127 and 128. • The shuttle was modified again—see below. Shuttle changes [ ] With each major new version came changes in the shuttle: Models Shuttle assembly part number Shuttle body part number Notes Picture VS-1?? Originally like the 's shuttle, but there were many changes as the VS-1 evolved. • Singer parts lists give contradictory information about the 8301 shuttle body.
The parts lists state that both the 8227 and the 8327 shuttle assemblies use it, but the pictures given of those assemblies show completely different shuttle bodies. The correct answer is probably 8327 because shuttles found in the wild stamped '8301' or sometimes '301' are the later wasp-waisted sort. None of the four shuttle models can be substituted for each other; if they even fit at all, they will cause skipped stitches. However, there was once an aftermarket of replacement shuttles, and the replacements were sometimes contrived to be compatible with both the 27/28 and 127/128 models. Consequently there are extant shuttles which have no stamped part number and which bear the features of both the 8301 and 54504. Variations [ ] Once production settled down into the model 27 and 28 versions, Singer produced many variants that were intended for different cabinets and power sources.
The variant number was listed after the version number and (except for the K designation) a dash; for example, the model 27 standard treadle variant is '27-3'. Variant Difference 27-1, 28-1, 127-1, 128-1 standard treadle variant, designation later changed to 3 to avoid confusion with V. 1 version* 27-2, 28-2, 127-2, 128-2 standard hand-crank variant, designation later changed to 4 to avoid confusion with V. White Sewing Machine Company's 'Number 8', a copy of the model 127 At about USD100 apiece (about USD2500 adjusted), Singer sewing machines were pricey, even considering the payment plans and trade-in allowances that were offered. The high prices created a demand for knock-offs made by bargain competitors.
The main competitors were and, who sold copied Singer models made by a variety of manufacturers: Manufacturer Singer model Knock-off name Goodrich Machine Sewing Company VS-1? Minnesota The Free Sewing Machine Company VS-2 ACME The Davis Sewing Machine Company VS-2 Minnesota-B, Burdick Illinois Sewing Machine Company 27 New Royal White Sewing Machine Company 27 Franklin, 'Long Shuttle' White Sewing Machine Company 127 Number 8 Domestic Sewing Machine Company 27 Franklin Domestic Sewing Machine Company 127 Minnesota-A, Minnesota New Model A, Minnesota-H Standard Sewing Machine Company VS-2? Minnesota-L Power [ ] The 27 model series had three options for power: foot, hand crank, and external electric motor. Diagram of treadle table from 1896 instruction manual A treadle obtains power from the user's legs. Early treadles were for just one foot making a heel-toe rocking motion, but all later treadles, including those offered with 27-series machines, were for two feet making a left-heel-right-toe (or vice versa) motion. The treadle provided with 27-series machines has a negative: one complete down-up motion produces exactly four stitches. As a foot treadle, the machine mounts in a cabinet about the size of an adult schooldesk.
The treadle pad is built into the cabinet's base right at the user's feet. A round leather 'treadle belt' passes up from the treadle, up through the cabinet, over the handwheel by following the belt groove, back down through the cabinet again, and then back to the treadle.
The belt is joined end-to-end with a clip to make a loop, and can be shortened and reclipped (using special 'treadle belt pliers') as needed to keep proper tension. The treadle belt is tanned leather, 3/16' in diameter, and is normally sold in 72' lengths.
Hand crank [ ]. Model 128 with hand crank Hand cranks provide greater portability at the cost of greater exertion. A hand crank machine fit in a small case, making it a piece of luggage rather than a piece of furniture.
It also cost significantly less than a full treadle. Indeed, the 3/4th size model 28/128 derivative was specifically intended for this end. The crank is geared to give a negative so that it can crank the machine at high speed.
Each rotation of the crank handle produces three rotations of the handwheel, and hence three stitches. External electric motor [ ] Electric motors were offered (by Singer and others) to retrofit these and other treadle machines with electric power. Cabinet-mount [ ].
Philip Diehl's treadle-controlled electric motor Early electric conversions consisted of mounting a motor in the treadle cabinet. The treadle belt was shortened to run only from the motor's pulley to the handwheel. The treadle pad was then given a mechanism for controlling the motor's speed in the manner of a modern car gas pedal. These conversions were invented and developed by, an inventor under contract with Singer. His efforts bore fruit in 1884, before the first VS-1 was even built and fully five years before Singer's first natively electrified model. He continued to make improvements for many years thereafter. Pillar-mount [ ].
Figure 3 from Frederick Diehl's pillar-mount motor patent Later motor kits dispensed entirely with the treadle, treadle belt, and cabinet. The motor bolted right to the machine's pillar, where—thanks to its compact size—it could remain even when the machine was tilted into its cabinet or enclosed within its cover. This was an improvement over earlier pivoting-motor designs, large offset belt-drive motors, and the many schemes for entirely replacing the handwheel with a motor. Credit for the original idea may belong to George F. Green, who proposed it back in 1879 but was probably unable to build or obtain the sufficiently compact motor required by his design.
It was Frederick Diehl and Martin Hemler, Singer employees, who finally developed the idea in 1921. Add-on motor kit showing pedal-controlled electrical outlet Speed is controlled by a, originally mounted on the treadle pad but later as an independent pedal for foot or knee control. The kit includes a dual electrical outlet that mounts alongside the machine in its case: one outlet is for the motor and is controlled by the foot pedal; the other is for a sewing lamp (see below) and is always energized. A sewing machine thus electrified now fit entirely inside a woman-portable carrying case. Electric motors became so common that Singer made provision for them: the model 127/128 'modernized' versions included mounting lugs for a motor, whereas earlier models had to be drilled and tapped. Some 127/128 machines were even given motors right at the factory, and of those, a few models used a smaller lighter solid handwheel instead of the larger heavier spoked handwheel used on machines sold as treadles. The spoked handwheel is better for treadles because its larger inertia keeps it spinning longer, whereas the lighter solid handwheel is better for motors because its smaller inertia causes it to start and stop more quickly.
Advertising card from 1920s showing motor kit () The add-on motor drives the handwheel by means of a rubber belt. Meanwhile the bobbin winder has a separate belt: the models 27 and 28 drive the bobbin winder using a long round or V belt to the motor, whereas the 'modernized' models 127 and 128 drive the bobbin winder directly off the handwheel by means of a small 'ring belt' or 'bobbin belt' acting as a tire.
Model Belt Belt race inner length Belt race outer length Adjustment range +/- V belt Stretch belt 27*, 28*, 127, 128 spoked handwheel motor belt 14-3/4 inches 15-3/4 inches 1/4 inch Singer 193077 (15-3/8 inches) Singer 2125 or Dritz 903 (13-1/2 inches) or similar 27*, 28*, 127, 128 solid handwheel motor belt?? 1/4 inch Singer 193066 (14-1/4 inches) Singer 2125 or Dritz 903 (13-1/2 inches) or similar 27, 28 bobbin winder belt 10-3/4 inches 11-7/8 inches 1/2 inch see below see below 127, 128 bobbin winder tire 5/8 inch 1-1/8 inch 0 not applicable Singer 15287A (included in Singer 2125 and Dritz 903) • Models 27 and 28 do not have a motor mount hardpoint; the hardpoint appeared later on the models 127 and 128.
Without a hardpoint, screw holes must be manually drilled and tapped into the pillar for the motor mounting bolts. Unfortunately there is not a standard location for these screw holes, and so the add-on motor can be mounted anywhere within a two-inch range on the pillar. Consequently, the belt race length can vary from the standard race lengths of the 127 and 128. If it does vary, then the standard Singer V belts can be too long or too short. In that case a stretch belt (good over a range of several inches) will suffice instead.
Difficulties with 27/28 bobbin winder belt [ ]. An extra pulley tack-welded on, to drive the bobbin winder Models 27 and 28 were designed before electrified sewing machines were common, and the location of the bobbin winder reflects this. It is positioned to intercept the treadle belt as it passes back down into the cabinet. Motorization removes the treadle belt and so opens the question of how to drive the bobbin winder. To answer this, the modernized models 127 and 128 moved the bobbin winder up several inches where, with a suitable tire, it can run directly off the handwheel.
The older 27 and 28, on the other hand, require a dedicated belt to drive the bobbin winder, but the motor kit only has one pulley, resulting in problems: • Driving both the handwheel and the bobbin winder with a single belt running in a triangular path causes traction problems at the motor, due to decreased belt contact area (from 90 degrees to about 60 degrees). This can be compensated by high belt tension, but that in turn will wear out the bearings and quickly exhaust a stretch belt. • Driving the bobbin winder with a separate belt, hooked onto the motor pulley whenever needed, means that the standard V belt cannot be used to drive the handwheel.
A less-desirable stretch belt, easier to get onto and off the motor pulley, must be used instead. One solution to the problem has been spotted in a wild: tack-weld a second pulley onto the motor pulley, as shown in the picture. Sewing lamp [ ]. Diagram from Diehl's Singerlight patent Motor kits usually included a sewing lamp.
Singer's motor kits and factory motorizations each included one of two different sorts of lamp: • Spotlights cast their light in just one direction and are known to run hot. They attach at any screw-hole on the machine, using a short metal arm with thumbscrew. • 'Singerlights' have an elongated bulb and shade which casts its light over most of the bed. They attach to the machine's pillar access port underneath the round cover, sharing its thumbscrew.
The Singerlight compatible with 27-series machines is Singer part number B428. It was originally invented by Frederick Diehl in 1921, and a coworker soon followed with additional patented improvements. As there were many clones of the add-on motor, so also were there many clones of the Singerlight., aka MEPM, was one of the third-party vendors of such products. Finish and decals [ ] Most machines in this model series are painted in lacquer, but some of the later variants (127-12, 127-14, 127-23, 128-8, 128-12, 128-14, and 128-18) were instead finished in the newly fashionable, low-glare 'black wrinkle' (aka 'Godzilla' or 'black crinkle') finish.
They were all then 'ornamented' with extensive eye-catching decals. Common decal sets have names and are shown below; alternatively, many machines carry nondescript floral patterns. 14' puzzle box Singer accessory kits were sold in fold-out 'Style' boxes, numbered consecutively as newer versions evolved from older ones. The numbers begin at 1 ('Style No. Keygen Adobe Acrobat Pro Dc Mac here.
1') and culminate at 14 during the era of the 27 model series. The boxes included accessory attachments for, braiding, underbraiding,,,,, and, plus spare needles,, screws, and screwdrivers. Today such a box is called a 'puzzle box', but this is a recent term: it is not mentioned in the original Style manuals. • • Singer's serial number archives (see External Links section) are incomplete yet list dozens of 50,000+ unit allocations of serial numbers • The official 'Adjuster's Manual' is written in plain English and is sufficiently illustrated for use by laymen. The manual is still sold today, and also offered online as a free download; see links section for URL. • • • • Many more details, and full references, about Wilson, Porter, and Baker are available in the page. Reimage Code Key. • 'Newburgh; her institutions, industries and leading citizens; Historical, descriptive and biographical' (1891) compiled by John J.